160-6 Meter Solid State Linear Amplifier [ TEN-TEC ]

[Tens de ter uma conta e sessão iniciada para poderes visualizar esta imagem]

Generating 100 Watts of output from as little as 5 Watts of input, the Model 418 Amplifier raises the bar for reliable and efficient recreational, emergency, and even contest communications.

TEN-TEC Engineers have utilized state of the art, silicon MOSFET technology to allow continuous 100% duty cycle operation in both CW and SSB modes. The model 418 is also compliant with AM, FM, AFSK, and PSK modes of operation. This amplifier also offers full QSK CW keying plus hot switching protection.

Measuring only 3.625″ X 6.5″ X 7.6″ inches and weighing just 5.4 lbs, the Model 418 will operate from any 13.8VDC (+/- 15%), 20 Amp power source.

Designed to interface with the new TEN-TEC Model 539 QRP Transceiver, the Model 418 amplifier can be easily connected to most low power transmitter designs (1 to 20 Watts). The amplifier’s comprehensive User’s Manual and TEN-TEC’s industry standard Technical Support department make set up quick and easy.

The Model 418 can switch bands automatically or manually. It also has a two position manual antenna switch. Bypass operation allows low power operation until higher power is needed. RF Sensing will automatically switch bands for you when the 418 is keyed with other rigs and the delta button is turned off.

The Model 418’s large LCD front panel readout gives the operator essential information about Output Power, SWR, Operating Voltage, and even Operating Temperature.

- 418 Product Brochure
- 418 Manual
- 418 Schematics

Amplifier typical gain: 13db
RF input: 1 to 20 watts
Operating Voltage: 13.8 volts +/- 15% (20 amp power source required)
Frequency Range: 160 through 6 meters (ham bands only)
RF output Power: 100 Watts, +/- 1 db (with typical 5 watts drive)

Operating Modes: AM, FM, AFSK, PSK, SSB, CW
Duty Cycle: 50% (TX/RX) 100 watts output. 100% for CW and SSB
Front Panel Display: Custom FSTN monochrome LCD
Display Back Lighting: 6 LEDs,for more than 200 color options
Cooling: 2 internal fans, temperature controlled
Harmonic & Spurious Outputs: -50dBc Typical @ 100 Watts HF, -60dBc Typical 6 Meters
Third Order Intermod: 30 dB below peak
Dimensions (HxWxD): 3.625” x 6.5” x 7.6” (excluding feet and connectors)
Weight: 5.4 lbs Shipping Weight 7 lbs
DC Power Connector: Power Poles
Fuse (back panel): 25 Amp, Automotive Blade Style
Key Jack: 1/8” Stereo Tip-Key In Ring-Key Out
ACC Din Connector: 8 Pin DIN, Key In, Clock/Data/Enable, Ground
Construction: Molded Plastic bezel, Aluminum chassis, front & rear panels & textured painted steel covers
Antenna Impedance: 50 ohms nominal
Automatic fault for: Antenna mismatch(output power >50 watts), Over current, Over temperature, and high input power
Works with most antennas (SWR less than 3:1)
Easy plug and play operation with Ten-Tec model 539 QRP radio
Separate antenna connector provided for automatic switch to six meter antenna
Works with most QRP rádios
RF connectors: 1 RF input, 3 RF outputs (two HF & One 6 meter)
Amplifier keyed from direct connection to foot switch, hand switch, or straight key. Key Out from amplifier is provided to key radio.

Price: $785.00

- Link